||150A / 950A
||Sensorless Brushless Motor
||1/8th Touring Car, Buggy, Truggy and Monster Truck
||Brushless Motor Limit with 4S LiPo/12 cells NiMH: KV≤3000 (4274 size motor)
Brushless Motor Limit with 6S LiPo/18 cells NiMH：KV≤2400 (4274 size motor)
|LiPo / NiMH Cells
||3-6S LiPo / 9-18S NiMH
||V/7.2V Switchable, Continuous Current of 6A (Switch-mode BEC)
||Powered by the stable BEC voltage of 6V/7.2V
|Size / Weight
1. Running Mode
- Option 1: Forward with Brake
- The vehicle can go forward and brake but cannot reverse in this mode. This mode is usually for racing.
- Option 2: Forward / Reverse with Brake
- This mode provides the braking function, it’s usually for training. “Forward/ Reverse with Brake” mode adopted the “DOUBLE-CLICK” method, that is your vehicle only brakes (won’t reverse) when the 1st time you push the throttle trigger forward (away from you) (1st push). If the motor stops when you quickly release the throttle trigger and then re-push the trigger quickly (2nd push), the vehicle will reverse. If the motor does not stop, then your vehicle won’ t reverse but brake, and you need to push the throttle trigger one more time. The vehicle only reverses after the motor stops. This method is for preventing vehicle from being accidentally reversed.
2. LiPo Cells
We strongly recommend setting this item manually instead of using the default setting “Auto Calc. (which means calculating the LiPo cells automatically)”. The ESC can only identify 3S, 4S
and 6S LiPo packs when setting this item to “Auto Calc.”. After you power on the ESC, if the battery voltage is below 13.6V, it will be identified as a 3S, if the voltage is from 13.6V to
17.6V, it will be identified as a 4S, if the voltage is above 17.6V, it will be identified as a 6S.
- This ESC is not intended for 2S operation. Even if you can set the “LiPo Cells” to 2S, it still does not work.
- You need to set “LiPo Cells” to “Auto Calc.” and “Cutoff Voltage” to “Disabled” if you use a NiMH pack or a 5S LiPo.
3. Low-Voltage Cutoff
Sets the voltage at which the ESC lowers or removes power to the motor in order to either keep the battery at a safe minimum voltage (for Lipo batteries). The ESC will monitor the battery
voltage all the time, it will immediately reduce the power to 50% and cut off the output 10 seconds later when the voltage goes below the cutoff threshold. The RED LED will flash a short,
single flash that repeats (☆, ☆, ☆) to indicate the low-voltage cutoff protection is activated. If you use a NiMH pack, then please set the “Cutoff Voltage” to “Disabled”.
- Option 1: Disabled
- The ESC won’t cut off the power due to low voltage after you select this option. We do not recommend using this option when you use any LiPo pack (5S LiPo is an exception), otherwise you will irreversibly damage it. However, for avoiding losing power in racing due to low voltage, we recommend using this option (this still may cause damage to your battery). You need to select this option when you use a NiMH pack.
- Option 2: Auto (Low)
- Low cutoff voltage, not very easy to get the LVC Protection activated, is applicable to batteries with poor discharge capability.
- Option 3: Auto (Intermediate)
- Medium cutoff voltage, prone to getting the LVC Protection activated, is applicable to batteries with ordinary discharge capability.
- Option 4: Auto (High)
- High cutoff voltage, very prone to getting the LVC Protection activated, is applicable to packs with great discharge capability.
Warning: If you set the Cutoff Voltage to Disabled when you use a LiPo pack, then please pay attention to the power change of your vehicle. In general, the battery voltage gets very low level when your vehicle is severely losing power, then you should stop using that pack.
4. ESC Thermal (Shutdown) Protection/Overheat Protection
The ESC will automatically cut off the output and the GREEN LED will flash a short, single flash that repeats (☆, ☆, ☆) when the temperature gets up to the value you preset and activates the ESC thermal protection. The output won’t resume until the temperature gets down.
5. Motor Thermal (Shutdown) Protection/Overheat Protection
This item has been permanently set to “Disabled” by manufacturer.
6. Motor Rotation
Pull the throttle trigger with the motor shaft faces you, the motor spins counter clockwise if this item is set to CCW; the motor spins clockwise if set to CW. The (A/B/C) wiring order of motors from different manufacturers may vary, so the direction of the motor rotation may be opposite to what you expect. You can adjust the “Motor Rotation” or swap any two (ESC-to-motor) wires if the motor runs in reverse.
7. BEC Voltage：
- Option 1：6.0V
- It’s applicable to ordinary servos. Do not use this option with high voltage servos; otherwise your servos may not function normally due to insufficient voltage.
- Option 2：7.2V
- It’s applicable to high voltage servos. Do not use this option with ordinary servos; otherwise your servos may be burnt due to high voltage.
8. Max. Brake Force
This ESC provides the proportional braking function; the braking effect is decided by the position of the throttle trigger. It sets what percentage of available braking power is applied with full brake. Large amount will shorten the braking time but it may damage your pinion and spur. Please select the most suitable brake amount as per your car condition and your preference.
9. Max. Reverse Force
Different reverse amount will bring different reversing speed. For the safety of your vehicle, we recommend using a low amount.
10. Start Mode (Punch)
You can choose the punch from level 1 (very soft) to level 5 (very aggressive) as per the track, tires, grip, your preference and etc. This feature is very useful for preventing tires from slipping during the starting-up pr ocess. In addition, “level 4” and “level 5” have strict r equirement on battery’s discharge capability. It may affect the starting-up if the battery discharges poorly and cannot provide large current in a short time. The car stutters or suddenly loses power in the starting-up process indicating the battery’s discharge capability is not good, then you need to reduce the punch or increase the FDR (Final Drive Ratio).
11. Drag Brake
Drag brake is the braking power produced when releasing the throttle trigger to neutral zone. This is to simulate the slight braking effect of a neutral brushed motor while coasting. (Attention! Drag brake will consume excess power, frequent use of accel and brake may damage the ESC. Please apply it cautiously.)